Ktc KPC-EW650NU Manuel d'utilisateur télécharger pdf

M168-EW650U-001

HIGH PERFORMANCE

CCTV CAMERA

OPERATION MANUAL

Thank you for choosing our high quality camera.

Before attempting to connect or operate, please read and

follow these instructions.

NAME AND FUNCTION

• LENS CONNECTION

Lenses are sold separatele. Lenses such as an auto iris lens,

CS-Mount lens and C-Mount lens can be used.

NOTE

• Please keep the lens clean.

• Any foreign objects and fingermarks on the lens can cause

inferior image quality in low light level conditions.

When using an auto iris lens

1.Please peel off about 8mm of the

outer skin of the auto iris lens cable.

2. Please peel off about 2mm of the

outer skin of the insulated conductor

inside the lens cable.

3. Please remove the cover of the auto iris lens connection plug and solder

the lens cable ti the connector pin in the plug.

*PIN ASSIGNMENT OF THE LENS CONNECTOR

Signal for DC + iris lens

Pin 1: DAMP-

Pin 2: DAMP+

Pin 3: DRV+

Pin 4: DRV-(GND)

Signal for Video + iris lens

Pin 1: Power source: +9 DC,50mA MAX

Pin 2: N.C(Not used)

Pin 3: Video Signal:0.7Vp-p/10K ohms.

Pin 4: Shield, ground

4. Please replace the auto iris lens connection plug cover and take off the

CCD protection cap and than attach the auto iris lens to the camera by

screwing it in clockwise.

Back Focus Procedure

Step 1 - Remove Lens Cover.

Step 2 - If using a C-Mount lenses it can be applied

to the camera at this time.

Step 3 - Most current lenses are CS-Mount and

require removal of the C/CS ring.

Step 4 - To remove the C/CS ring loosen but do not

remove completely the two set screws and

than remove the C/CS ring.

Step 5 - Screw on the CS-Mount lens until a good

picture is obtained and tighten the set screws.

Step 6 - Use the focus ring on the lens to obtain

a finer focusing

NOTE

- if a C-Mount lens was applied and focus could not be obtained, please try the following :

• Ensure that the lens is in face a C-Mount and not a CS-Mount.

•Check the focus adjust on the lens.

• if need be loosen the set screws and adjust the position of the lens

and C/CS ring as one unit until a good focus is obtained.

5. Please insert the connection plug that is connected to the auto iris lens cable into the

auto lens connector, which is located on the back of the camera

* As the connecting method varies with instruments, refer to the

manual supplied with the instrument.

* Only connect the cable when the power is turned off.

* Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modications in construction of this devies which are not

expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

Caution -

CAUTION

1. A regulated DC12V 300mA power supply is recommended for use with

this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be

out of subject.

2. It is recommended that the camera is used with a monitor that has a

CCTV quality 75 video impedance level. If your monitor is switched to

high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the

internal componets. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.”

Note -

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

WARNING -

CAUTIONS CAUTIONS

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European

countries with separate collection systems)

This marking shown on the product or its literature, indicate that

it should not be disposed with other household wastes at the end

of its working life. To prevent possible harm to the environment or

human health from uncontrolled waste disposal, please separate

this from other types of wastes and recycle it responsibly to

promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details

of where and how they can take item for environmentally safe

recycling.

Business users should contact their supplier and check the terms

and conditions of the purchase contract.

Household users should contact either the retailer where they for

disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO

QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence

of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufcient mangnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance(servicing) instruction in

the literature accompanying the appliance.

COMPONENTS

FRONT

BACK

CS-Mount

C-Mount

Lens Cover

C/CS RING

INSTALLATION

• MONITOR CONNECTION

BNC FEMALE

VIDEO

DC12V REGULATED

POWER SUPPLY

VIDEO IN

①. ■ MENU BUTTON

▲ UP BUTTON

▼ DOWON BUTTON

◀ LEFT BUTTON

▶ RIGHT BUTTON

②. Auto IRIS Jack

CS-MOUNT ADAPTOR RING

Set Screw(Left Side)

AUTO

IRIS

OSD

CONTROL

①

②

High Performance

DSP Color Camera

Auto Iris Lens

Connection Plug

C-mount Adaptor Ring

Spare Screw (Machine 2x2) - 2ea

Operation Manual

1 2

Résumé du contenu

Page 1 - CCTV CAMERA

M168-EW650U-001HIGH PERFORMANCECCTV CAMERAOPERATION MANUALThank you for choosing our high quality camera.Before attempting to connect or operate, plea

Page 2 - HIDDEN MENU

OSD MANUALSPECIFICATIONDIMENSIONSUnit(mm)MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENULENSMANUAL AUTOTYPE DC / VIDED SPEED 000

Commentaires sur ces manuels

Pas de commentaire

Ktc KPC-EW650NU Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Caméscopes Ktc KPC-EW650NU. KT&C KPC-EW650NU User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Caméscopes Ktc KPC-EW650NU