Ktc KNC-VNi120HD Manuel d'utilisateur télécharger pdf (Page 2)

5. Assign an IP address

To make it accessible on the network, the Network Camera must be assigned an IP address.

Note:

•

A network DHCP server is optional.

•

The Network Camera has the default IP address 192.168.0.123.

•

If IP assignment fails, check that there is no firewall blocking its operation and check that the Network

Camera and your computer's IP is located on the same subnet.

Assign an IP address using IP Installer

IP installer automatically search and display KT&C network devices on your network. The application

can also be used to manually assign a static IP address.

Note:

The computer running the IP installer must be on the same network segment (physical subnet) as the Network

Camera.

1. Check that the Network Camera is connected to the network and that power has been applied.

2. Start KT&C IP installer.

3. When the Network Camera is displayed as shown above, select the unit that need to be assigned

an IP.

A. Refresh Device List – Rescan local network to nd the Network Camera.

B. Authenticate – Enter the administrator ID and password.

* Default User ID and Password is [ID: admin, Password: admin]

C. Host Name – Enter the Host Name of the Network Camera.

D. IP Settings

i. Dynamic – Assign dynamic IP address automatically from DHCP server on your network.

ii. Static – Assign static IP address manually.

iii. Port – Enter the HTTP port the Network Camera will use. The default setting is 80.

Alternatively, any port in the range 1024-65535 may be used, but check rst with your

system administrator before changing the default setting.

E. Network Settings

i. Subnet Mask – Specify the mask for the subnet the Network Camera located on.

ii. Gateway – Specify the IP address of the default router (gateway) used for connecting devices

attached to different networks and network segments.

iii. Pri. DNS – Enter the IP address of the primary DNS server. This server provides the

translation of host names to IP addresses on your network.

iv. Sec. DNS – Specify the IP address of the secondary DNS server. This will be used if the

primary DNS server is unavailable.

4. Click the “Set” button to save conguration.

Accessing the Network Camera

1. Start your browser(when you rst run ActiveX to install, run an “IE as Administrator” on Window 7 or Vista).

2. Enter the IP address or host name of the Network Camera in the Address eld of your browser.

3. If you are accessing the Network Camera for the rst time, you will see the following warning

message as shown below.

4. Click the warning message and select “Install ActiveX Control…”.

5. Click “Install” to install the KT&C Web Viewer.

6. If a Windows Security Alert pop-up appears, click “Unblock”.

7. After installing the KT&C Web View ActiveX Control, a Login page will be displayed.

Enter the user ID and password.

Note:

Default User ID and Password is [ID: admin, Password: admin]

8. The video image displays in your browser.

Note:

To view streaming video in Microsoft Internet Explorer, you must set your browser to allow the “KT&C Web Viewer” to

be installed on your computer. This ActiveX component is installed the first time a video stream is accessed.

6. Terminal Block Connectors

KNC-VDi100HD, KNC-VNi100HD, KNC-VDi120HD, KNC-VNi120HD are connected with external

equipment as following diagram below.

Circuit diagram

1. INPUT – Connect the external sensor e.g. PIR motion sensor. (3.3V DC pull-up built in)

A. ON - Short-circuit with GND.

B. OFF - Open

CAUTION :

Digital Input must not be exposed to voltages greater than 10V DC.

2. OUT – Connect the external alarm e.g. light or buzzer.

CAUTION :

If used with an external relay, a diode must be connected in parallel

with the load, for protection against voltage transients.

CAUTION

: Max. load = 70mA Max voltage = 12V DC.

Example of terminal connection

TERMINAL CONNECTION

KNC-VDi100HD

1 2

Commentaires sur ces manuels

Pas de commentaire

Ktc KNC-VNi120HD Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Caméscopes Ktc KNC-VNi120HD