Ktc KNC-HDi47 Manuel d'utilisateur télécharger pdf

3. Product Description

Description and Function

Board Lens Type Pinhole Lens Type

1. Reset Button – Press the reset switch for more than 10 seconds,

the restore the camera to the function default settings.

2. Service Video Connector – Outputs video to the monitor.

3. Status LED

4. MIC Hole

5. Micro SD Card Socket.

6. NTSC / PAL slide Switch.

7. Power Input(DC12V) – Connects to DC 12V power.

8. Network Connector –

The Network Camera connects to the network via a standard

network cable, and automatically detects the speed of the local network segment

(10BaseT/100BaseTX Ethernet). PoE Supported

M175-HDi47-001

Megapixel Network Camera

KNC-HDi47 Installation Guide

Table of Contents

1. INTRODUCTION

2. PACKAGE CONTENTS

3. PRODUCT DESCRIPTION

4. HARDWARE INSTALLATION

5. IP ADDRESS ASSIGNMENT

6. PRODUCT SPECIFICATIONS

1. Introduction

IP Dome Camera Installation Guide

This installation guide provides instructions for installing the Network Camera on your

network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package.

Installation Steps

1. Check the package contents against the list below.

2. Read the Product description.

3. Install the hardware.

4. Set an IP address.

5. Set the admin and user ID and password. (see User’s Manual)

Important! : This product must be used in compliance with local laws and regulations.

2. Package Contents

Network Camera Mounting Bracket PoE B'D Cable

Software CD Video Output Test Cable Installation Guide Screws

4. Hardware Installation

IP camera are designed to be installed using a template as shown below.

Camera Mounting Position

Connection

1. Connect the camera to the network using a UTP cable (CAT.5), Power can be supplied via the network cable (PoE)

2. Connect DC 12V to the power terminal. This is not necessary if the Network Camera is connected to a PoE hub or midspan.

3. Check that the indicator LEDs indicates the correct conditions.

4. Connect the analog monitor to the service video connector for adjusting focus, then press and quickly release the reset

switch for focus assistant mode. Then you can select normal view or focus view mode using the reset switch.

Caution: When you use focus assistant mode, “Focus View” mode is recommended for more exact focus.

Caution: Focus assistant mode will be automatically exited after 3 minutes for normal operation.

* Option

➐

➑

Reset

Micro SD

NTSC

SERVICE

VIDEO OUT

P A

Reset

Micro SD

NTSC

SERVICE

VIDEO OUT

P A L

➍ ➍➊ ➊➌ ➌➏ ➏

➎ ➎➋ ➋

❶

Machine Screw:

M2.6 x 3.5(2ea)

CAUTION !

Please start installing

in the order shown.

Tapping Screw:

ø3 x 8(2ea)

1 2

Résumé du contenu

Page 1 - Megapixel Network Camera

3. Product DescriptionDescription and FunctionBoard Lens Type Pinhole Lens Type1. Reset Button – Press the reset switch for more than 10 seconds,

Page 2 - 6. Product Specications

5. IP Address AssignmentTo make it accessible on the network, the Network Camera must be assigned an IP address.Note: • A network DHCP server is optio

Commentaires sur ces manuels

Pas de commentaire

Ktc KNC-HDi47 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Caméscopes Ktc KNC-HDi47. KT&amp;C KNC-HDi47 User Manual [en] [es] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Caméscopes Ktc KNC-HDi47

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Caméscopes Ktc KNC-HDi47. KT&C KNC-HDi47 User Manual [en] [es] Manuel d'utilisatio